Active

Contract Opportunity

The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract as Lowest Price Technically Acceptable (LPTA) Evaluation Factors for the item listed below. The required item is for commercial item prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice.

The Contract Line Item (CLIN) is as follows:

CLIN 0001 Qty 2 3276C076

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222ST4N8C3960NANN; Continuous Length Stud, 1/2”-13UNC-3A X 60” Long. NICU 400, Uncoated, Type IV Style C.

CLIN 0002 QTY 16 3276C077

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required;

General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222N1X6C30NBNN; Plain Hex Nut, 3/8”-16UNC-3B. NICU 405, Uncoated, Washer or Chamfer face

CLIN 0003 Qty 5 3276C078

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222ST4N10C3960NANN; Continuous Length Stud, 5/8”-11UNC-3A X 60” Long. NICU 400, Uncoated, Type IV Style C.

CLIN 0004 Qty 24 3276C079

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222N1X8C30NBNN; Plain Hex Nut, 1/2”-13UNC-3B. NICU 405, Uncoated, Washer or Chamfer face

CLIN 0005 Qty 2 3276C081

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222ST4N6C3576NANN; Continuous Length Stud, 3/8”-16UNC-3A X 36” Long. NICU 400, Uncoated, Type IV Style C.

CLIN 0006 Qty 152 3276C082

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222N1X12C30NBNN; Plain Hex Nut, 3/4”-10UNC-3B. NICU 405, Uncoated, Washer or Chamfer face.

CLIN 0007 Qty 7 3276C080

A: Studs, Bolts, Screws and Nuts for Applications Where a High Degree of Reliability is Required; General Specification For, MIL-DTL-1222 J; 08 December 2000

B: M1222ST4N 12C3960NANN; Continuous Length Stud, 3/4"-11 UNC-3A X 60" Long. NICU 400, Uncoated, Type IV Style C.

CLIN 001-007 REMAINING DATA IS ALL THE SAME AS LISTED BELOW

C: Latest Revision

D: N/A

E: N/A F: N/A G: N/A H: N/A

I: N/A J: N/A K: N/A L: N/A

M: All reports required. NOTE: “Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (New Untested) fastener is required for each of the two methods, and both of these tests shall be reported.”

N: N/A O: N/A P: N/A

Q: Inspection IAW 4.3.2 & 4.3.2.1

R: Acceptance criteria IAW 4.3.2 & 4.3.2.1

S: NDT procedures and acceptance criteria IAW 4.3.3

T: N/A

U: Commercial packaging with thread protection

V: N/A W: N/A X: N/A Y: N/A Z: N/A

AA: N/A BB: N/A

The requirement will be solicited as a total small business set aside. The NAICS code applicable to this procurement is 332722, Hardware & Abrasives with a size standard of 600 employees. The Product Service Code is 5305. The solicitation document incorporates provisions and clauses in effect through FAC 2024-01 and DFARS Change Notice 10/30/2023.

The anticipated delivery date for this acquisition is 4 April 2024. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. THE SOLICITATION IS NOT YET AVAILABLE.

The solicitation number is SPMYM124Q0030, and it is expected to be available on or about 22 January 2024 and posted to SAM.gov, https://sam.gov/ Quotes will be due by 05:00 PM EST on 26 January 2024. Responses to the solicitation notice shall be emailed to the attention of Ronald Martin at ronald.c.martin@dla.mil . Please make sure that the solicitation number (SPMYM124Q0030) is included in the subject line of any email correspondence. Emails without subject lines will not be read because of security issues.

Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offeror's to access solicitation documents posted. Prospective Offeror's should also register at on the interested vendor list under SPMYM122Q0030. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed.

All responsible sources may submit a proposal which may be considered by the Government. By submitting a quote, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the solicitation, except for awards to foreign vendors for work to be performed outside the United States. Lack of registration in the SAM database will make an offeror ineligible for award. Offerors may obtain information on registration and annual confirmation requirements by calling 1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in accordance with the solicitation, dates and procedures. Please direct all questions regarding this requirement to Ronald Martin at ronald.c.martin@dla.mil.

Attachments/Links